Product ID:SCOTCHWELD 1838B ADHESIVE TAN (PT B)
MSDS Date:01/01/1987
FSC:8040
NIIN:00-823-7944
MSDS Number: BFQYZ

3M COMPANY - ADHESIVES COATINGS & SEALERS DIV

Emergency Phone: 612 733 1110 OP55

Cage: 04963

3M MINNESOTA MINING AND MFG CO ADHESIVES SEALERS DIV

SAINT PAUL, MN 55144-1000 US

Telephone: 800-364-3577/651-737-6501(24 HOURS)

Cage: 04963

EPOXY RESIN

Fraction By Weight: 75.0%

N-BUTYL GLYCIDYL ETHER (BGE)

CAS: 2426-08-6

RTECS: TX4200000

Fraction By Weight: 12.0%

OSHA PEL 50 PPM

ACGIH TLV: 25 PPM; 9293

SILICA, AMORPHOUS, DUST

CAS: 112945-52-5

RTECS: VV7310000

Fraction By Weight: 13.0%

OSHA PEL 6 MG/M3

ACGIH TLV: 10 MG/M3; 8990

Effects of Overexposure:EYE:IRRT ON DIRECT EXPOS. SKN:IRRT,
SENSITIZATION POSSIBLE. INH:IRRT NOSE,THROAT. INGES:NEG EFFECT.

First Aid:EYE:FLUSH 10 MIN W/WATER, CALL PHYS. SKN: WASH THOROUGHLY
SOAP & WATER. INH:REMOVE TO FRESH AIR. INGES:NO ACTION INDICATED.

Extinguishing Media:CO*2, DRY CHEMICAL, FOAM, WATER
Fire Fighting Procedures:USE SCBA IN FIRES INVOLVING THIS MATERIAL
Unusual Fire/Explosion Hazard:NONE

Spill Release Procedures:OBSERVE ALL PRECAUTIONS. COLLECT SPILL & PLACE
IN APPROVED CONTAINER. CLEAN UP RESIDUE, WIPE UP AREA.

Handling and Storage Precautions:USE ONLY IN WELL VENTILATED AREAS.
PREVENT CONTACT W/EYES & SKIN. WASH CONTAMINATED CLOTHING BEFORE
REUSE.AVOID INHL DUST.
Other Precautions:BUTYL GLYCIDYL ETHER IS SUSPECTED MUTAGEN.

Respiratory Protection:USE DUST MASK WHEN GRINDING OR SAWING CURED
RESIN.
Ventilation:VENT CURING OVENS TO OUTDOORS. PROVIDE LOC EXH IN CONF
AREAS
Protective Gloves:USE IMPERVIOUS
Eye Protection:USE SAFETY GLASSES
Other Protective Equipment:NONE
Supplemental Safety and Health
PART B OF TWO PART SCOTCHWELD 1838B/A TAN EPOXY ADHESIVE KT. UPDATE PER
3M MSDS 4NOV85 (OSHA) DOC# 1O31426. 3M GENERIC ID# IS
62-1614-XXXX-X.FORMER P/N:SCOTCHWELD EC1838B TAN.

HCC:V7
Spec Gravity:1.3
Viscosity:350000 CPS
Solubility in Water:VERY SLIGHT
Appearance and Odor:TAN, VISCOUS PASTE WITH LITTLE ODOR
Percent Volatiles by Volume:0

Stability Indicator/Materials to Avoid:YES
Hazardous Decomposition Products:HCL, CO, CO*2, SMOKE PARTICLES WHEN
EXP EXCESS HEAT OR FLAME

Waste Disposal Methods:CURED RESIN: DISPOSE IN APPD LANDFILL OR
INCINERATE PER REGS. INCINERATE UNCURED WASTE IN APPROVED DISPOSAL
FACILITY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.